Semi Automatic Tube Filler Machine With Ultrasonic Sealing Equipment
  • Model: VK-TFS-002U
  • Power Supply: 220V/50HZ/Single phase
  • Power: 1500w
  • Frequency: 20Khz
  • Tube Length: 40-280mm
  • Tube Diameter: 10-80mm
  • Filling volume: A: 5-30ml B: 6-60ml C: 10-120ml D: 25-250ml E: 50-500ml (Optional)
  • Size: 735*670*1300mm
  • Weight: 130kg
View Video

Function And Application

Use ultrasonic to weld plastic soft tube tail. Do not need any adhesive or filler or solvent when welding, do not consume large amounts of heat, and easy to operate, high welding speed, high efficiency.

This machine is widely used in toothpaste, cosmetic, medical product, food and industrial tubes etc.

Main Parameters

filling tubes sealing equipment (1).jpg

5pcs for filling sealing.jpg

ModelVK-TFS-002U
Power Supply220V/50HZ/Single phase
Power1500w
Frequency20Khz
Tube Length40-280mm
Tube Diameter10-80mm
Filling volumeA:5-30ml B: 6-60ml C: 10-120ml D: 25-250ml E: 50-500ml (Optional)
Size735*6701300mm
Weight130kg

Sealing Machine Layout

drawing of filler sealer.jpg

  1. Main body
  2. Sensor
  3. Tube Hight adjustment
  4. Front mould
  5. Back mould
  6. Cutter
  7. Gas-pressure meter
  8. Gas-pressure adjustment
  9. Emergency button
  10. Start button
  11. PLC
  12. Holder
  13. Moulds gap adjustment
  14. Power lamp
  15. Power switch
  16. Tune
  17. OSC check
  18. Over load lamp
  19. Loading meter

(Remark: Pls checking the Front mould Screw if with strong lock, as afraid when the transportation and screw is loose)

ultrasonic sealer equipment.jpg

Sealing Part

  • Motor start: this is for control the Tube holder running
  • Feeding cylinder start: this is for control the Tube holder feeding
  • Ultrasonic cylinder start: this is for control the up mould and down mould working.
  • Trimming cylinder start: this is for control the cutter
  • Fill Cylinder: This is for control the Filler head cylinder star or Stop when manual
  • Fill start: This is for control the filling star or stop when manual
  • Ultrasonic start: This is for control the frequency, this is same as the “18. OSC check”
  • Tube Orientation on: this is for control the Sense off/on
  • Time setting: This is for Adjusting the Delay time/ Welding time/Holding time
  • Delay time: 0.80
  • Welding time: Tube Dia 20, the time will about: 0.20, Tube dia 30, the time will about 0.40, Tube dia 40, the time will about 0.50, Tube dia 50, the time will about 0.7
  • Holding time: 0.35

Filling Part

filling part.jpg

Operation Process

ultrasonic tubes sealing illustration.jpg

  1. Connect power and compressed air correctly (suggest 0.5MPa).
  2. Press the Power switch
  3. Press ‘OSC check’ button and set ‘Tune button’ at the same time, Pls using the screw on the Tune button, you can turn to Left or Right, while find the minimum of ‘Signal light’ (it will about low than 1A) fixed ‘Frequency adjustment’. (do not press ‘OSC check’ continuously, press it intermittently)
  4. Put tube on the holder.
  5. Press ‘Ultrasonic cylinder start’, front mould and back mould will be closed. set ‘Moulds gap adjustment’, let two moulds just touch and no gap. Press ‘Cutter controller’ and confirm the cutter will work smoothly.(need to put the plastic tube on the tube holder when you adjusting)
  6. Set front mould and back mould and cutter at original position.
  7. Put tube on the ‘Holder’ and press ‘Feeding cylinder start’, the tube will run between two moulds. Adjust the height of holder if necessary. (suggest tube is higher than back mould 2 to 3 mm)
  8. Make tube back to original position.
  9. Set to auto status, turn on sensor if tube has color code otherwise turn off it.
  10. Press ‘Auto’ the machine will work automatically.

Samples

ultrasonic tubes sealing equipments.jpg

tubes sealing samples for South Africa customer (3).jpg

tubes samples for ultrasonic sealing machine.jpg

Failure and Remedy

 FailureCauseRemedy
Machine doesn’t work or work abnormalNo power or compressed airConnect power and compressed air
Low compressed air pressureEnhance air pressure
Plastic overflow or not good after weldingTwo moulds too closed or too partedAdjust the gap between two moulds
Rough edge after cuttingCutter bluntSharpen cutter or replace sharp one
Cutter has large gap between back mouldMake cutter touch back mould